Memory-mapped I/O ports on CX II

From Hackspire
Jump to navigation Jump to search

Not all parts have been discovered and researched yet, so the information on this page is not complete.

00000000 - Boot1 ROM

128kB of on-chip ROM.

10000000 - SDRAM

64 MiB, managed by 0x90120000.

90000000 - General Purpose I/O (GPIO)

See GPIO Pins

90010000 - Fast timer

The same interface as 900C0000/900D0000, see Second timer.

90020000 - Serial UART

PL011.

90030000 - Unknown

Probably some kind of hash/crypto thing.

90040000 - SPI controller

FTSSP010 SPI controller connected to the LCD.

90060000 - Watchdog timer

Possibly an ARM SP805 or compatible.

90070000 - Second Serial UART

PL011.

90080000 - Unknown

Unknown. Probably an FTSSP010 as well.

90090000 - Real-Time Clock (RTC)

Similar to the ARM PrimeCell PL031, but interrupt registers are different.

  • 90090000 (R): Current time, increments by 1 every second.
  • 90090004 (R/W): Alarm value. When the time passes this, interrupt becomes active.
  • 90090008 (R/W): Sets the value of 90090000 (clock will not read new time until a couple seconds later). Reads last value written.
  • 9009000C (R/W): Interrupt mask (1-bit)
  • 90090010 (R/W): Masked interrupt status, reads 1 if interrupt active and mask bit is set. Write 1 to acknowledge.
  • 90090014 (R): Status
    • Bit 0: Time setting in progress
    • Bit 1: Alarm setting in progress
    • Bit 2: Interrupt acknowledgment in progress
    • Bit 3: Interrupt mask setting in progress

900A0000 - Miscellaneous

Seems to be similar to CX and Classic, except for the model ID at 900A0000 which is now 0x202.

900B0000 - ADC

A Faraday FTADCC010.

900C0000 - First timer

Same port structure as Second timer.

900D0000 - Second timer

Timer is a SP804.

900E0000 - Keypad controller

See also Keypads for information about the keypads themselves.

  • 900E0000 (R/W):
    • Bits 0-1: Scan mode
      • Mode 0: Idle.
      • Mode 1: Indiscriminate key detection. Data registers are not updated, but whenever any key is pressed, interrupt bit 2 is set (and cannot be cleared until the key is released).
      • Mode 2: Single scan. The keypad is scanned once, and then the mode returns to 0.
      • Mode 3: Continuous scan. When scanning completes, it just starts over again after a delay.
    • Bits 2-15: Number of APB cycles to wait before scanning each row
    • Bits 16-31: Number of APB cycles to wait between scans
  • 900E0004 (R/W):
    • Bits 0-7: Number of rows to read (later rows are not updated in 900E0010-900E002F, and just read as whatever they were before being disabled)
    • Bits 8-15: Number of columns to read (later column bits in a row are set to 1 when it is updated)
  • 900E0008 (R/W): Keypad interrupt status/acknowledge (3-bit). Write "1" bits to acknowledge.
    • Bit 0: Keypad scan complete
    • Bit 1: Keypad data register changed
    • Bit 2: Key pressed in mode 1
  • 900E000C (R/W): Keypad interrupt mask (3-bit). Set each bit to 1 if the corresponding event in [900E0008] should cause an interrupt.
  • 900E0010-900E002F (R): Keypad data, one halfword per row.
  • 900E0030-900E003F (R/W): Keypad GPIOs. Each register is 20 bits, with one bit per GPIO. The role of each register is unknown.
  • 900E0040 (R/W): Interrupt enable. Bits unknown but seems to be related to touchpad. Causes interrupt on touchpad touched.
  • 900E0044 (R/W): Interrupt status. Bits unknown. Write 1s to acknowledge.
  • 900E0048 (R/W): Unknown

90120000 - SDRAM Controller

An FTDDR3030.

90130000 - Unknown Controller for the LCD Backlight

The OS controls the LCD backlight by writing to 90130018.

90140000 - Power management

A new "Aladdin PMU" unit. Not much known.

A4000000 - Internal SRAM

0x40000 bytes SRAM, managed by the controller at ?.

A8000000 - Internal SRAM

0x25800 bytes SRAM for an LCD framebuffer, managed by the controller at ?. It might be bigger in reality, but the OS only ever accesses 320*240*2 Bytes.

B8000000 - SPI NAND controller

An FTSPI020 with a MICRON 1Gb flash at CS 1.

C0000000 - LCD controller

A PL111.

C8010000 - Triple DES encryption

Implements the Triple DES encryption algorithm.

  • C8010000 (R/W): Right half of block
  • C8010004 (R/W): Left half of block. Writing this causes the block to be encrypted/decrypted.
  • C8010008 (R/W): Right 32 bits of key 1
  • C801000C (R/W):
    • Bits 0-23: Left 24 bits of key 1
    • Bit 30: Set to 0 to encrypt, 1 to decrypt
  • C8010010 (R/W): Right 32 bits of key 2
  • C8010014 (R/W): Left 24 bits of key 2
  • C8010018 (R/W): Right 32 bits of key 3
  • C801001C (R/W): Left 24 bits of key 3

CC000000 - SHA-256 hash generator

Implements the SHA-256 hash algorithm, which is used in cryptographic signatures.

  • CC000000 (R): Busy if bit 0 set
  • CC000000 (W): Write 0x10 and then 0x0 to initialize. Write 0xA to process first block, 0xE to process subsequent blocks
  • CC000008 (R/W): Some sort of bus write-allow register? If a bit is set, it allows R/W access to the registers of the peripheral, if clear, R/O access only. Don't know what it's doing here, but it's here anyway.
  • CC000010-CC00004F (R/W): 512-bit block
  • CC000060-CC00007F (R): 256-bit state

DC000000 - Interrupt controller

See Interrupts. The controller is a PL190.

Retrieved from "https://hackspire.org//index.php?title=Memory-mapped_I/O_ports_on_CX_II&oldid=1716"